Configure the Line Level Password

router(config) #

line console 0 line aux 0

• Enters line configuration mode (console, auxiliary, or vty)

router(config-line)#

login

• Enables password checking at login router(config-line)# password password

• Sets the line-level password

Boston(config)#line con 0 Boston(config-line)#login Boston(config-line)#password ConUser1

Boston(config)#line con 0 Boston(config-line)#login Boston(config-line)#password ConUser1

Console Port

By default, the Cisco router console ports allow a hard BREAK signal (within 60 seconds of a reboot) to interrupt the normal boot sequence and give the console user complete control of the router. This is used for maintenance purposes, such as when running the Cisco router password recovery procedure. Even though this hard BREAK sequence is, by default, available to someone who has physical access to the router console port, it is still important to set a linelevel password for users who might try to gain console access remotely. The hard BREAK sequence may be disabled using the no service password-recovery command.

Note If a router is configured with the no service password-recovery command, all access to the ROM Monitor (ROMMON) is disabled.

By default, the console port does not require a password for console administrative access. However, you should always configure a console port line-level password. There are two ways to configure a console line password: You can enter the password during the initial configuration dialog, or you can use the password command in the console line configuration mode.

VTY Lines

Cisco routers support multiple Telnet sessions (up to five simultaneous sessions, by default— more can be added), each serviced by a logical vty. By default, Cisco routers do not have any line-level passwords configured for these vty.

5-90 Implementing Secure Converged Wide Area Networks (ISCW) v1.0

If you enable password checking, you must also configure a vty password before attempting to access the router using Telnet. If you fail to configure a vty password, and password checking is enabled for vty, you will encounter an error message similar to the following:

Telnet 10.0.1.2

Password required, but none set

[Connection to 10.0.1.2 closed by foreign host]

There are two ways to configure a vty password: You can enter the password during the initial configuration dialog, or you can use the password command in line vty configuration mode.

The following are a few more things to consider when securing Telnet connections to a Cisco router:

■ If you fail to set an enable password for the router, you will not be able to access privileged-EXEC mode using Telnet. Use either the enable password or enable secret password command to set the enable password for your routers.

■ Telnet access should be limited only to specified systems by building a simple access control list (ACL) that does the following:

— Allows Telnet access from specific hosts only

— Implicitly or explicitly blocks access from untrusted hosts

— Ties the ACL to the vty lines using the access-class command

— This example shows ACL 30 restricting Telnet access only from host 10.0.1.1 and implicitly denying access from all other hosts for vty 0 to 4:

Boston(config)#access-list 30 permit 10.0.1.1 0.0.0.0 Boston(config)#line vty 0 4 Boston(config-line)#access-class 30 in

■ You must configure passwords for all of the vty lines on the router. Remember that you can add more vty lines to the router and these lines must be protected as well as the default 0 to 4 lines.

Auxiliary Lines

By default, Cisco router auxiliary ports do not require a password for remote administrative access. Administrators sometimes use auxiliary ports to remotely configure and monitor the router using a dialup modem connection.

Unlike console and vty passwords, the auxiliary password is not configured during the initial configuration dialog and should be configured using the password command in auxiliary line configuration mode.

If you wish to turn off the EXEC process for the aux port, use the no exec command within the auxiliary line configuration mode.

Setting the auxiliary line-level password is only one of several steps you must complete when configuring a router auxiliary port for remote dial-in access. The table explains commands used when configuring an auxiliary port.

© 2006 Cisco Systems, Inc. Cisco Device Hardening 5-91

Commands to Configure an Auxiliary Port

Command

Explanation

Boston(config)#line aux 0 Boston(config-line)#modem inout

Permits incoming and outgoing modem calls on this line

Boston(config-line)#speed 9600

Sets the line speed that should be used to communicate with the modem

Boston(config-line)#transport input all

Allows all protocols to use the line

Boston(config-line)#flowcontrol hardware

Enables Ready to Send (RTS) and Clear to Send (CTS) flow control

Boston(config-line)#login

Authenticates incoming connections using the password configured on the line

Boston(config-line)#password NeverGuessMeAux

Configures the password NeverGuessMeAux to authenticate incoming calls on this line

5-92 Implementing Secure Converged Wide Area Networks (ISCW) v1.0

Continue reading here: The no service passwordrecovery command prevents console from accessing ROMMON

Was this article helpful?

+1 0

Readers' Questions

  • Callisto
    Why is the login command required?
    9 months ago
  • when accessing a switch The login command is required when accessing a switch to ensure that only authorized users are granted access to the switch. By requiring authentication, the switch can be sure that only authorized users are making changes to the configuration, or accessing sensitive information.
    • bisrat
      How to set user exec password?
      1 year ago
      1. Log in as an administrator or with an account that has administrator privileges.
      2. Open the Control Panel and select User Accounts.
      3. Select the user account you want to set the password for and click the "Set Password" option.
      4. Enter and re-enter the password you want to use and click the "OK" button.
      5. You will be asked to enter a hint to help the user remember the password in case it is forgotten. Enter the hint and click the "OK" button.
      • nannie
        Which type of router connection can be secured by the accessclass command?
        1 year ago
      • Access-class command is used for securing Telnet and SSH connections to a Cisco router.
        • Jonne
          How to setup password level in router?
          1 year ago
        • To set up password protection on a router, create a username and password and then set up access control. Log in to the router’s web interface, go to the access control or security page, and enter the username and password. Then choose the types of access the user should have, such as Full Access or Limited Access. After that, save the settings.
          • bacco
            What is line vty password?
            1 year ago
          • The "line vty password" is a command used in Cisco IOS networking devices to set the password for virtual terminal lines (Telnet or SSH sessions) on the device. It allows network administrators to restrict access to privileged command modes by configuring a password that must be entered when attempting to connect to the device remotely.