Verification of Dialer Profiles

Çtico-oom

]}i n_Ar R hjit.n i r djtbsL -itiJc Iji^ise up m?" VÎ>Ïi^r ijv [r-ir 1 1 1. 1-lii. : 1 T ]

Timj* until iiiMtii«* 10 £ a®Ci ClltluelL ljill -juiinjulajUl OU UJ; iy

SF-IC; B-Clunnal 'i tftlr. Himnr (lîil men) . idle! fciiTjar |2i> rnrnl

Hut tvr ;iiTi»r [JO . Re-«n«bl« Hi iSÎSh Di^li^r etizr —=Llii

© 2004 Cisco Systems, Inc. All rights iesei\ecl. BCRAN v2.1—7-2

Lnn-: ntjihiin

The show dialer interface bri number command displays information in the same format as the legacy DDR statistics on incoming and outgoing calls.

In the figure, the message "Dialer state is data link layer up" suggests that the dialer came up properly.

If the message "physical layer up" is displayed, it means that the line protocol came up but the Network Control Protocol (NCP) did not.

In the figure, "Dial reason" refers to the source and destination addresses of the packet that initiated the dialing.

Ikj^vU* LjlJcfltJWTL

STJ LEOCi liytcn, BW nO Ktait, DLY aDDOO unnn, rely llLHi*, lmd l/25£

sulatian f'/X. los^bac/t not set DIE. la pula*d £ef 1 Si-iMda en riait

Tnl^Ji-r Pjioi1 iJ* tnrTri t^ TiETfl-

LuL lnptiL inr 3'J: , luL^uL fUvAt, QUt|)Ufc bidiuj i^dvu L-sijt ^loarLTifl or In 3V

Ikj^vU* LjlJcfltJWTL

STJ LEOCi liytcn, BW nO Ktait, DLY aDDOO unnn, rely llLHi*, lmd l/25£

sulatian f'/X. los^bac/t not set DIE. la pula*d £ef 1 Si-iMda en riait

Tnl^Ji-r Pjioi1 iJ* tnrTri t^ TiETfl-

LuL lnptiL inr 3'J: , luL^uL fUvAt, QUt|)Ufc bidiuj i^dvu L-sijt ^loarLTifl or In 3V

l>JtIWlT- fitted >

irfrr: l^i'ij bvyhnn, TiW Tttiihj dUU^t i . xwly Ir^rd 1.,'ih."-., tn-LiipjiulafPP, lenrpbjofc not eeL, JcnryHuia jluc sat IhtatrMa its IjLjim'i. Lu Dialer 1 ¡EiiiiijjHuLjLiii;i pp;:

The show interface dialer command displays information on incoming and outgoing calls.

In the figure, the messages "Dialerl is up, line protocol is up" and "BRI0:1 is up, line protocol is up" suggest that the dialer came up properly.

The message "Interface is bound to BRIO:1" informs you that this dialer is bound to the 1 B channel.

You also know that BRIO: 1 is active and that the PPP encapsulation has been applied by the dialer interface.

© 2004 Cisco Systems, Inc. All rights reserved.

0 0

Post a comment